Recent content by shumax

  1. S

    V1 G.2 Died on Me :/

    Will check in the morning....
  2. S

    V1 G.2 Died on Me :/

    Update: Sent mine in and had it back in a day and a half. Seems to work fine so far...
  3. S

    V1 G.2 Died on Me :/

    No reply to the email I sent, by 12pm. I called, after their lunch break, at 1pm. Very nice lady answered the phone and instantly sent me a Fedex label to overnight it back. I dropped it off at my local spot at 4pm . They told me it would take less than a day to "flip" it, so I'm encouraged...
  4. S

    V1 G.2 Died on Me :/

    Add me to the list on the power issue. I purchased two units in March-ish. The second one was a few weeks after the first and it is having the issue. Ironically, it's been in my wifes car and we've put 200 miles on it since March. So, it literally saw no use. Followed the directions to...
  5. S

    V1G2 arrived today and.....the new Redline is released! (BLEEP)

    I have a hard time believing the new Redline is THAT much better to justify it's price. I may be alone, but that pricing is obnoxious...
  6. S

    R3 k-band tuning suggestions

    Thanks, all. He lives in Cincinnati, Ohio and travels the tri-State area there - Norther Kentucky, Southern Indiana. Also, trips down to TN, NC and SC. I will have him try those settings and see what happens. I think the "K-block" is too risky, but that's just me. He understands, generally...
  7. S

    R3 k-band tuning suggestions

    I have a friend with an R3 that is worn out with all of the BSM falsing. What is the best firmware options/settings to apply to quiet it down to the point he will actually use it? Thanks!
  8. S

    Who else is holding on to their V1 while waiting for the V2 issues to get worked out

    I'm not near as "scientific" as many of you, here; however, I can tell you the Gen2 is a step up from the Gen 1, even running custom frequencies and with V1Driver. That combo quieted it down, for sure. But! The range on the Gen2 reminds me of AT LEAST what the Uniden R3 returned and the BSM...
  9. S

    Question on V1Driver

    Thanks, all! iOS for my phone. Used V1Driver for years on the gen 1. Just a few months on gen 2. I enabled the setting for ALWAYS in settings; also toggles the alerts within the app itself. Will try it on the toad tomorrow. Thanks again!
  10. S

    Question on V1Driver

    Is there a way to have it connect to the Gen 2 each time it powers on in my car? My Gen 2 is hard wired and comes on with the ignition. Seems I have to go in and activate the app, each time, in order for it to connect. While running, can it kick a shadow box up that shows the frequency of a new...
  11. S

    V1 Gen 1 and Gen 2 Permanent Mount

    Agree! The stock mount works wonderfully. But! It won't stick to that area on my windshield due to the film that you see. Those clear areas, inside the black, - the dimples? The black section is "higher" than the clear dimple area. That creates an air pocket and won't allow the suction cup...
  12. S

    V1 Gen 1 and Gen 2 Permanent Mount

    Correct. Scraping mine does no harm at all. Was/is perfectly fine.
  13. S

    V1 Gen 1 and Gen 2 Permanent Mount

    I don't think we are. I don't have aftermarket window tint up there. It's the raised black dots that it's stuck to. If it were aftermarket tint? Yes, it would be scratched badly by the razor. Scarping the black dots? I didn't notice any change to it after I was done doing that. FYI...
  14. S

    V1 Gen 1 and Gen 2 Permanent Mount

    It did not impact the tint strip a bit. No issues with the scraping.
  15. S

    V1 Gen 1 and Gen 2 Permanent Mount

    I had to scrape it with a razor. I'm not going to say it's a 10sec. process, but I got it off in a min. or two. The fact you can position it EXACTLY as you like, and that it works well? Bonus - why not? It's not like V1 doesn't give you extra suction cups, either. Seems like $5 (for the...
Top