2018 GMC Sierra ALP Install (fronts)

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
I received my ALP kit yesterday so like any kid with new toys I had to start playing with them immediately.

I had inspiration from some of the other threads of 2014-18 Sierra installs and this is how I did it.
Took about 5 hours +1 bonus hour because one head connector wasn't quite right.
Sorry the engine bay is pretty dusty
IMG_20190720_181132.jpg

Ran sensor wires through the firewall using the grommet on the driver's side right in front of the door

IMG_20190720_142138.jpg

IMG_20190720_142149.jpg
IMG_20190720_142156.jpg


Once all the cables were fished through the front fender to the engine bay I routed them to their respective spots.
IMG_20190720_142206.jpg

Removed the cowl at the front of the engine bay, mounted all the sensors level and connected them to their respective leads.
Some pictures of the routing I used. I used zip ties and 3M tape on some rub points/sharp spots just to be safe.
View attachment 125983
IMG_20190720_181138.jpg

IMG_20190720_181141.jpg
IMG_20190720_181146.jpg

IMG_20190720_181513.jpg


Inside the truck I have the Hifi speaker and GPS module in the dash under the steering column. All of the wiring is spooled up and tucked away under the dash or near the firewall.
IMG_20190720_181044.jpg
IMG_20190720_181049.jpg


I used a micro2 add a fuse for power and didn't take any pictures under the dash!
IMG_20190720_181056.jpg


Overall it was not too painful to install. Planning to have it tested soon
 

Logan T

PSL +5
Intermediate User
Premium Member
Joined
Nov 4, 2018
Messages
206
Reaction score
347
Location
ATL/Florida
Very nice! How many sensors are you running and where did you put them :)
 

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
@Logan T I have 2 Rx and 1 Tx - the Rx are in the bottom slats/Tx right under the M! I used your thread for some inspiration :)
 

Logan T

PSL +5
Intermediate User
Premium Member
Joined
Nov 4, 2018
Messages
206
Reaction score
347
Location
ATL/Florida
@Logan T I have 2 Rx and 1 Tx - the Rx are in the bottom slats/Tx right under the M! I used your thread for some inspiration :)
Ah I see from that one pic it looks really good! I think that will perform really well. That's the best place for the TX it also makes it look clean and blended in as best as possible. If that doesn't perform well you can just move the RX sensors either to the same slat as the TX or one above like mine but I think that will do well. Hopefully you can find someone with Dragon and you'll know for sure how covered you are.
 

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
Yeah I hear there might be a dragon tester or two floating around in AB - hopefully I can track one down!
 

nighthawk

Learning to Fly
Beginner User
Joined
Jul 6, 2016
Messages
307
Reaction score
310
Nicely done. Looks like an easy install in comparison with some cars!
 

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
Ended up adding some rears as the local speed camera enforcement is actually a Truspeed S out the back of a pickup truck. I also travel to Edmonton on occasion/Hwy 2.
Haven't had the rear tested yet - hopefully someone in the Edmonton area can hook me up or @Tripleturbo once he's feeling better!
24 inch radius goes to about the top corner of the tail light from bubbles, overlap on plate - the RX may be a tad too close together.
Truck needs a wash.
IMG_20191202_153050 - Copy.jpg
 

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
Nicely done. Only issue would be snow haha.
Yeah snow definitely can block them pretty easily, I also have to consider snow/dirt build up on longer drives in the winter depending on road conditions.
I've yet to actually have a legit hit :(
 

Heywood

Learning Something New, Still Dying Stupid
Advanced User
Lifetime Premium Member
Joined
May 12, 2016
Messages
3,996
Reaction score
7,526
Location
Alberta Canada
I think I’m 13.5 “ from the center of the TX to the inside edge of the RX on both sides for the rears.

It was shot with a DETC and was JTG front and back. I shot it myself as well.
 

Attachments

Gatortotz

Learning to Drive
General User
Lifetime Premium Member
Joined
Apr 23, 2019
Messages
35
Reaction score
40
Location
AB, Canada
I think I’m 13.5 “ from the center of the TX to the inside edge of the RX on both sides for the rears.

It was shot with a DETC and was JTG front and back. I shot it myself as well.
Yeah mine is definitely a little more spread out than yours. I expect it will perform pretty well. I gotta find someone with a DETC! :p
 

Kennyc56

Ford Lover-I/O hater!
Advanced User
Lifetime Premium Member
Joined
Feb 22, 2018
Messages
3,002
Reaction score
7,719
Location
I/O Hell, Aka Eastern N.C.
Great looking install! I only wish the back of my Boss 302 was that easy! The rears will be my next project.
 
Last edited:

V1Jake

Advanced User
Premium Member
Joined
Oct 31, 2010
Messages
5,110
Reaction score
5,094
Location
On the highway

Discord Server

Latest threads

Forum statistics

Threads
80,036
Messages
1,217,820
Members
20,254
Latest member
ford
Top